Module điều khiển độ sáng đèn chiếu sáng ICP DAS LC-223H CR

Thương hiệu: ICP DAS | Tình trạng: Còn hàng

Liên hệ

1-channel Dimmer Control Module

THÔNG TIN SẢN PHẨM

Features

Isolated Analog Output (0 to 20 mA, 0 to 10 V, 1 to 10 V) For Dimming Control
Relay Operation Current: 16 A (Res. Load)
Support Lighting Module (Max.):
Incandescent Lamp: 40W/ 220VAC * 8 Sets
LED(Electronic ballast): 40W/ 220VAC * 10 Sets
Provide Power Relay Output to turn ON/OFF the Dimming Ballast
Isolated Analog Output(0 to 20 mA, 0 to 10 V, 1 to 10 V) for Dimming Control
Provide the wall Switch function to Control the Brightness of the Dimming Ballast
Provide The Dry Contact to trigger the Brightness of the Dimming Ballast
Supports Modbus RTU and DCON Protocols
2500 VDC Intra-Module Isolation
±2 kV SURGE,±4 kV ESD and EFT Protectio
DIN-Rail Mounting

Introduction

The LC-223H is an easy-to-use dimming ballast control module that can be easily installed and operated without requiring specialist knowledge or skills. The brightness of a fluorescent lamp can be controlled using a dimmer, either via digital input or a host controller. The digital input can be used to directly control the light value of the luminous flux in sequence from 10% to 100%, without the need for a remote host controller. 4 kV ESD,2kV SURGE protection and 2500 VDC intra-module isolation are also provided. When required, communication with the LC-223H is programmable based on the Modbus RTU/DCON protocol, with the added benefit that diff erent addresses can be set via hardware configuration.

Specifications

Isolation
Intra-module Isolation	2500 VDC

EMS Protection
EFT (IEC 61000-4-4)	±4 kV for Power
ESD (IEC 61000-4-2)	±4 kV contact for each Terminal ±4 kV Air for Random Point
Surge (IEC 61000-4-5)	±2 kV for Power

LED Indicators
Status	1 LED as Power Indicator

Analog Output
Channels	1
Type	0 ~ 20 mA, 4 ~ 20 mA, 0 ~ 10 V, 1 ~ 10 V
Resolution	12-bit
Accuracy	±0.1% of FSR
DA Output Response Time	10 ms
Voltage Output Capability	20 mA
Current Load Resistance	450 Ω

Digital Input
Channels	Dry Contact: 2 for the Dimming Trigger Wet Contact: 1 for the Wall Switch Control
Type	Wet Contact, Dry Contact
Wet Contact, ON Voltage Level	65 VAC ~ 240 VAC
Wet Contact, OFF Voltage Level	58 VAC Max.
Dry Contact, ON Voltage Level	Close to GND
Dry Contact, OFF Voltage Level	Open

Relay Output
Channels	1
Type	Power Relay, Form A (SPST N.O.)
Contact Rating	16 A (Res. load) (1).250 VAC (Recommend Working Current 1.5 A)
Operate Time	10 ms Max.
Release Time	5 ms Max.
Electrical Endurance	120,000 ops.
Mechanical Endurance	5,000,000 ops.
Power on Value	Yes, programmable
Safe Value	Yes, programmable
Application Specification	(1).Incandescent Lamp: 40W/220VAC * 8 Sets (2).LED (Electronic ballast): 40W/220VAC * 10 Sets

COM Ports
Ports	1 x RS-485
Baud Rate	1200 ~ 115200 bps
Data Format	(N, 8, 1)
Protocol	DCON, Modbus RTU

Power
Reverse Polarity Protection	Yes
Consumption	1.5 W Max.
Powered from Terminal Block	Yes, 10 ~ 30 VDC

Mechanical
Dimensions (mm)	72 x 100 x 59 (W x L x H)
Installation	DIN-Rail

Environmental
Operating Temperature	-25 ~ +75°C
Storage Temperature	-30 ~ +80°C
Humidity	10 ~ 95% RH, Non-condensing

Download

Data sheet

Documents

Ordering infromation

LC-223H CR

1-channel Dimmer Control Module with 2-channel Dry Contact Input Trigger (RoHS)

Module điều khiển độ sáng đèn chiếu sáng ICP DAS LC-223H CR

Sản phẩm đã được thêm vào giỏ hàng

Sản phẩm đã được thêm vào giỏ hàng