Module điều khiển đèn chiếu sáng ICP DAS LC-102H CR

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

2-CH Lighting Control Module with AC Load Current Measurement (2 AC DI + 2 Relay output)

Gọi +84 904251826 để được trợ giúp

Module điều khiển đèn chiếu sáng ICP DAS LC-102H CR

Feature

  • High Power Relay Output to Turn On/Off the Lighting
  • Number of Lighting Fixtures That Can Be Connected:
    • Incandescent Lamp: 40 W/ 220 VAC * 5 Sets
    • LED(Electronic ballast): 40 W/ 220 VAC *8 Sets
  • 0 to 5 A AC power Load Current Measurement Relay output
  • Isolated AC Digital Input
  • Node Addresses by Hardware Configuration
  • Low Power Consumption
  • Modbus RTU and DCON Protocols

Introduction

The LC lighting control module is easy-to-use and requires no specialist skills to install and operate, and no software is needed in order to control the lighting control channels.
 
The LC-102H is a 2-channel lighting control module with AC load current measurement which provides 2-channel high power relay output and 2-channel AC digital input.
 
The AC load current measurement is provided in the relay control loop. This function not only allows the user to know the load current value, but also through the measurement of the load current value, it can be used to know the switching state of the relay, whether the load is working normally in the light control loop, or the relay is stuck and cannot be switched.
 
The input channel can directly control the relay ON and OFF sequence without the host command.
 
When required, the module can be communicated with the Modbus RTU protocol, and an added benefit is that different addresses can be set for Modbus RTU communication via hardware configuration.

Application

Specifications

Software
Function Local and Remote Direct Control Relay ON/OFF and Remote Status Monitoring
EMS Protection
EFT (IEC 61000-4-4) ±4 kV for Power
ESD (IEC 61000-4-2) ±4 kV Contact for each Terminal
Surge (IEC 61000-4-5) ±2 kV for Power
LED Indicators
Status 1 LED as Power Indicator
Digital Input
Channels 2
Type Wet Contact, 90 ~ 240 VAC
ON Voltage Level 65 VAC
OFF Voltage Level 56 VAC
Isolation 3000 VDC
Input Impedance 68 KΩ, 2W
Relay Output
Channels 2
Type Power Relay, Form C (SPDT N.O+N.C..)
Contact Rating 30 A @ 250 VAC
AC Load Current Measurement Yes, 0 ~ 5 A range with 3% of FSR Accuracy.
Operate Time 15 ms Max
Release Time 22 ms Max.
Electrical Endurance 100,000 ops.
Mechanical Endurance 10,000,000 ops
Power on Value Yes
Safe Value Yes
Application Specification (1).Incandescent Lamp: 40W/ 220VAC * 5 Sets
(2).LED(Electronic ballast): 40W/ 220VAC *8 Sets
COM Ports
Ports 1 x RS-485
Baud Rate Hardware Configuration: Fixed 9600 bps
Software Configuration: 1200 to 115200 bps
Data Format N,8,1/O,8,1/E,8,1/N,8,2
Protocol Modbus RTU/DCON
Ethernet
Node Address 32 to 63 for hardware configuration
Power
Reverse Polarity Protection Yes
Input Range 10 ~ 30 VDC
Consumption 2.8 W Max.
Mechanical
Dimensions (mm) 72 mm x 95 mm x 57 mm
Installation DIN-Rail
Environment
Operating Temperature -25 ~ +75°C
Storage Temperature -30 ~ +75°C
Humidity 10 ~ 95% RH, Non-condensing

Download

Datasheet

Documents

Ordering Information

LC-102H CR  2-CH Lighting Control Module with AC Load Current Measurement (2 AC DI + 2 Relay output) (RoHS)

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: