Bộ chuyển đổi CAN sang Quang (Dual Fiber, Multi Mode, ST, 2KM) ICP DAS I-2533 CR

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

CAN to Multi-mode Fiber Bridge

Gọi +84 904251826 để được trợ giúp

Bộ chuyển đổi CAN sang Quang (Dual Fiber, Multi Mode, ST, 2KM) ICP DAS I-2533 CR


  • Support both CAN 2.0A and CAN 2.0B specification
  • Fully compatible with the ISO 11898-2 standard
  • Rotary switch for CAN baud rate configuration
  • Up to 100 CAN nodes on the CAN channel (*Note)
  • Transmission distance up to 2 km at any CAN baud rate
  • Provides the 512-record CAN Tx buffer and 512-record CAN Rx buffer
  • Allow user-defined baud rate
  • Software utility tool for message filter configuration
  • Fiber Port: ST (Multi-mode)
  • Broken line detection for fiber cable

Note: We have verified to drive 100 CAN nodes at the same time via one CAN port of I-2533.


The I-2533 is an intelligent CAN bridge that can be used to establish the connection between two CAN bus systems via fiber optic cable. Similar to the I-2532, the I-2533 can also apply in various CAN-based protocols to convert CAN bus signals to optical signals and reshape the CAN signals. The difference between the I-2532 and I-2533 is the CAN configuration functions and the distance limitation of CAN communication. The I-2533 offers the functions to configure the CAN baud rate and CAN message filters. These are useful when using the I-2533 to link two CAN networks which may have different baud rates. By using the I-2533, the transmission distance limitation of the CAN bus system will not be reduced because of the CAN baud rate, which means that the total network length can be extended. This feature means that users can develop the applications more powerful and flexible with the I-2533.


  • Control System
  • Building Automation
  • Factory Automation
  • Distributed data acquisition
  • EV(Electric Vehicle) charging station


LED Indicators
Status 1 x Power
3 x CAN status
1 x Fiber
COM Ports
Ports 1 x RS-232 (Utility Port)
Ports Multi Mode; ST connector x 1
Fiber Cable 50/125, 62.5/125 or 100/140 μm (62.5/125μm is recommended)
Wavelength 850 nm
Propagation Delay 250 us (*Note1)
Distance Between Stations 2 km max (62.5 / 125 μm recommended)
Ports 1
Baud Rate 10 k ~ 1 M bps
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminal Resistor Switch for 120Ω terminal resistor
Specification ISO-11898-2, CAN 2.0A and CAN 2.0B
Filter Yes
Input Range +10 VDC ~ +30 VDC
Consumption 3 W
Casing Plastic
Dimensions (mm) 32.3 x 77.5 x 99.0 (W x L x H)
Installation DIN-Rail
Operating Temperature -25 ~ +75 °C
Storage Temperature -30 ~ +80 °C
Humidity 10 ~ 90% RH, Non-condensing

Specification Memo

The propagation delay depends on the CAN Bus baud rate and the CAN message format. This value has been tested using a CAN baud rate of 1 Mbps, the CAN ID 0x12345678 and 8 bytes of data with a value of 0xFF.




Ordering Information

I-2533     CR  CAN to Multi-mode Fiber Bridge; 1 (2 km) multi-mode, ST connector (RoHS)

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: