Bộ chuyển đổi CAN/CAN FD sang Quang (Dual Fiber, Multi Mode, ST, 2KM) ICP DAS I-2533T-FD CR

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

CAN/CAN FD to Multi-mode Fiber Bridge

Gọi +84 904251826 để được trợ giúp

Bộ chuyển đổi CAN/CAN FD sang Quang (Dual Fiber, Multi Mode, ST, 2KM) ICP DAS I-2533T-FD CR

Feature

  • Compatible with the ISO 11898-2 standard
  • Compatible with CAN specification 2.0 A/B and FD
  • CAN FD support for ISO and Non-ISO (Bosch) standards switchable
  • CAN FD bit rates for data field from 100 kbps to 10000 kbps
  • CAN bit rates from 10 kbps to 1000 kbps
  • Fiber broken line detection
  • Support CAN Bus message filter configuration
  • Basic CAN message routing function via Group ID settings
  • Built-in switchable 120 ohm terminal resistor for CAN Bus
  • Dip switch for CAN/CAN FD baud rate configuration

Introduction

The I-2533T-FD is a local CAN/CAN FD (CAN with Flexible Data-Rate) bridge used to establish a connection between two CAN bus system via multi-mode fiber optic transmission medium. In order to solve the problem between CAN/CAN FD and fiber transmission medium. The I-2533T-FD is specially designed for converting the electrical CAN/CAN FD bus signal to fiber optic cables. Besides, I-2533T-FD has three more important features. First, the transmission distance limitation of the CAN bus system will not affected due to the different CAN/CAN FD baud rate. It means that the total CAN/CAN FD bus working distance can be extended. Second, the bus error on one CAN/CAN FD network will not affect the operation of another CAN/CAN FD network. Finally, the two CAN/CAN FD network can communication with each other by using different CAN/CAN FD baud rate for highly flexibility.

Application

  • Control System
  • Building Automation
  • Factory Automation
  • Distributed data acquisition

Specifications

LED Indicators
Status 1 x Power
3 x CAN status
2 x Fiber status
Fiber
Ports Multi-Mode; ST Duplex connector x 1; 100 Base-FX
Fiber Cable 50/125, 62.5/125 or 100/140 μm
Wavelength 1310 nm
TX Output -20 dBm Min. , -14 dBm Max.
RX Sensitivity -32 dBm Max.
RX Overload -8 dBm Max.
Budget 12 dBm
Propagation Delay 190 us (*Note1)
Distance Between Stations 2 km (62.5/125 μm recommended)
CAN
Ports 1
Baud Rate CAN bit rates: 10 k ~ 1 M bps,
CAN FD bit rates for data field: 100 k ~ 10M bps (*Note2)
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photocoupler
Terminal Resistor Switch for 120Ω terminal resistor
Specification ISO 11898-2, CAN 2.0 A/B and FD
Filter Yes
Power
Input Range +10 VDC ~ +30 VDC
Consumption 3 W
Mechanical
Casing Plastic
Dimensions (mm) 33 x 127 x 101 (W x L x H)
Installation DIN-Rail
Environment
Operating Temperature -25 ~ +75 °C
Storage Temperature -30 ~ +80 °C
Humidity 10 ~ 90% RH, Non-condensing

Specification Memo

Note1: The propagation delay depends on the CAN Bus baud rate and the CAN message format. This value has been tested using a CAN baud rate of 1 Mbps, the CAN ID 0x12345678 and 8 bytes of data with a value of 0xFF.
Note2: The maximum CAN FD data rate can be exceeded depending on the concrete operating conditions (cable length, network topology, settings,...), but it can also not be reached.

Download

Datasheet

Documents

Ordering Information

I-2533T-FD     CR  CAN/CAN FD to Multi-mode Fiber Bridge; 1 (2 km) multi-mode, ST connector (RoHS)

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: