I-7540D-MTCP-G CR: Bộ chuyển đổi Gateway CAN sang Ethernet Modbus TCP / Modbus RTU

Thương hiệu: ICP DAS | Tình trạng: Còn hàng

Liên hệ

I-7540D-MTCP-G CR CAN to Ethernet / Modbus TCP / Modbus RTU Converter (Plastic Case) (RoHS)

THÔNG TIN SẢN PHẨM

Features

80186-80 Embedded CPU, or compatible
Ethernet Protocols, TCP,UDP,IP,ICMP,ARP
COM driver support interrupt & 1K QUEUE Input & Output buffer
Provide 200 CAN frames buffer in CAN to Modbus Mode
NXP 82C 250 CAN Transceiver
Support both CAN specification 2.0A and 2.0B
Max transmission speed up to 1M bps for CAN and 115.2kbps for RS-232 & RS-485
Max transmission distance of CAN over 1000m (follow CAN specification)
7-segment LED display to Module IP, RS-232 baud rate, CAN configuration…
CAN Error/Tx/Rx LED indicator
Software configurable CAN and RS-232 communication parameters
Firmware updated from COM1 or Ethernet port
Support Web Configuration
Support maximum 24 Ethernet clients connection
Support function code 0x03/0x04/0x10 of Modbus TCP/RTU command for reading and writing CAN message
Provide the transparent communication between the CAN devices via Ethernet
Support 30 specific CAN IDs in the Modbus TCP/RTU mode\

Introduction

The I-7540D-MTCP is helpful for data exchanging between the Modbus devices and CAN devices. I-7540D-MTCP is a Modbus TCP server and acts as slave device in Modbus RTU network. It supports four communication modes: Modbus TCP, Modbus RTU, CAN-Ethernet Convert and Pair connection.

The major function of the I-7540D-MTCP is CAN to Modbus TCP/RTU gateway. It allows Modbus TCP/RTU device to communicate with CAN device on a CAN network. I-7540D-MTCP supports the function codes 0x03/0x04/0x10 of Modbus TCP/RTU for reading and writing CAN messages.

Furthermore, The device supports a transparent, protocol-independent transfer of the CAN messages, thus allowing its implementation into a wide range of possible applications. Furthermore, the CAN-Modbus Converter can be used with various higher layer CAN protocols (e.g. CANopen, DeviceNet or other proprietary protocols). The following figure shows the application architecture for CAN-Modbus Converter.

Specifications

LED Indicators
Status	1 x Power 3 x CAN status

COM Ports
Ports	1 x RS-232 1 x RS-485 (self-turner ASIC inside)
Baud Rate	110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Parity	None, Even, Odd
Data Bit	7, 8
Stop Bit	1

Ethernet
Ports	1 x RJ-45, 10/100Base-T(X)

CAN
Controller	NXP SJA1000T with 16 MHz clock
Transceiver	NXP 82C250
Ports	1
Baud Rate	10 k ~ 1 M bps
Isolation	1000 VDC for DC-to-DC, 2500 Vrms for photo-coupler
Terminal Resistor	Jumper for 120 Ω terminal resistor
Specification	ISO-11898-2, CAN 2.0A and CAN 2.0B
Filter	Yes

Power
Input Range	+10 VDC ~ +30 VDC
Consumption	2.5 W

Mechanical
Casing	Plastic
Dimensions (mm)	72 x 122 x 33 (W x L x H)
Installation	DIN-Rail

Environmental
Operating Temperature	-25 ~ +75 °C
Storage Temperature	-30 ~ +80 °C
Humidity	10 ~ 90% RH, Non-condensing

Download

Data sheet

Documents

Ordering Information

I-7540D-MTCP-G CR

CAN to Ethernet / Modbus TCP / Modbus RTU Converter (Plastic Case) (RoHS)

I-7540D-MTCP-G CR: Bộ chuyển đổi Gateway CAN sang Ethernet Modbus TCP / Modbus RTU

Features

Sản phẩm đã được thêm vào giỏ hàng

Sản phẩm đã được thêm vào giỏ hàng