I-7570 CR: Bộ chuyển đổi RS-232/422/485 sang HART

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

Serial To HART Converter (Gray Cover) (RoHS)

Gọi +84 904251826 để được trợ giúp

I-7570 CR: Bộ chuyển đổi RS-232/422/485 sang HART

Features

  • Support HART Short / Long frame
  • Support HART Burst mode
  • Support point-to-point or multi-drop HART mode
  • Support connecting up to 15 HART slave devices
  • Allow two HART masters
  • Provide utility tool for module configuration and HART communication
  • Provide PWR / TxD / RxD indication LED
  • Isolated COM 1: RS-232 / RS-422 / RS-485
  • 4KV ESD Protection
  • Built-in Watchdog
  • Selectable 250Ω load resistor
  • Support HART OPC Server provided by HART COMMUNICATION FOUDATION
    ( HART OPC Server : http://www.hartcomm.org/hcf/documents/documents_opc.html => for 30 day trial of the full licensed version )
  • Support FDT (Field Device Tool) technique and the below FDT software have been tested OK

(1) PACTware (PACTware)

(2) FieldCare (Endress+Hauser)

(3) PDM (Seimens)

Introduction

I-7570 is a Serial to HART converter and can be used as a HART master with HC_Tool utility or a HART slave with HDS utility.

(1) I-7570 as HART Master :

It allows users to access the HART slave by using RS-232 / RS-422 / RS-485. These HART slave devices may be a transmitter, actuator, current output device and so forth. In addition, by using the I-7570 utility tool, users can configure module and test HART communication easily and quickly.

(2) I-7570 as HART Slave :

ART Device Simulator (called HDS) is the HART device simulation software developed by ICP DAS. It can be used to simulate multi HART slave devices simultaneously to exchange data with HART master device by using ICP DAS HART converter (like: I-7567 / I-7570 / I-7547) connected to any COM port (USB / 232 / 485 / Ethernet). By this way, users can develop or verify the HART master program without any HART slave device.

Application

• Current Measuring
• Petrochemical Industry Application
• Environment Monitoring
• Tunnel Monitoring
• Monitor system
• Building Monitoring

FDT (Field Device Tool)

FDT (Field Device Tool) standardizes the communication and configuration interface between all field devices and host systems. FDT provides a common environment for accessing the devices' most sophisticated features. Therefore, by using ICPDAS HART converters, I-7567, I-7570 or I-7547, supporting FDT, users can easily and quickly construct HART online control and configuration system.

Specification

LED Indicators
Status PWR / TxD / RxD

 

COM Ports
Ports RS-232(Tx / Rx / GND) / RS-422 / RS-485
9-pin screwed terminal block
Baud Rate 1200 bps (For FW_v1.1)
1200 ~ 115200bps (For FW_v1.1 / HW_v1.2)
Data Format O(odd parity), 8(data bit), 1(stop bit) (For FW_v1.1)
N/O/E(parity), 8(data bit), 1/2(stop bit) (For FW_v1.1 / HW_v1.2)

 

HART
Ports 1
Protocol 2-pin screwed terminal block

 

Power
Reverse Polarity Protection Power reverse polarity protection, Over-voltage brown-out protection
Input Range Unregulated +10 ~ +30 VDC
Consumption 1 W

 

Mechanical
Dimensions (mm) 121 x 72 x 35 (H x W x D)
Installation DIN-Rail or Wall Mounting

 

Environmental
Operating Temperature -25 ~ +75 °C (-13 to 167 ℉)
Storage Temperature -30 ~ +85 °C (-22 to 185 ℉)
Humidity 5% ~ 95%, Non-condensing

Download

Data sheet

Documents

Ordering information

Serial To HART Converter (Gray Cover) (RoHS)  

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: