Module điều khiển chuyển động 4 trục ICP DAS I-8094A-G CR

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

High-speed 4-axis Motion Control Module with Internal CPU

Gọi +84 904251826 để được trợ giúp

Module điều khiển chuyển động 4 trục ICP DAS I-8094A-G CR

Feature

  • Independent 4-axis motion control
  • Support for hand wheel and jog functions
  • 2/3-axis linear / 2-axis circular interpolation function
  • Continuous interpolation function
  • Programmable T/S-curve acceleration and deceleration
  • A maximum pulse output rate of 4 Mpps for each axis
  • Pulse Output Types: CW/CCW or PULSE/DIR
  • 32-bit encoder counter for each axis
  • Encoder Pulse Input Types: A/B Phase or Up/Down
  • Programmable automatic homing for each axis
  • Position comparison management and software limits
  • A wide range of synchronous actions (event-triggered actions)
  • Can operate as a standalone module or in conjunction with a PAC

Introduction

The I-8094A is a 4-axis stepping/pulse-type servo motor control module that can be used on any of the ICP DAS PAC series controllers, and is suitable for general-purpose motion applications. The I-8094A has the full functions of the I-8094 and has an internal 80186 CPU allowing the module to be used to perform additional functions, including the ability to perform motion operations without requiring a PAC. When working with a PAC, it also allows users to perform additional functions by calling user-defined subroutines (Macro functions). Users can embed their customized processes (know-how) inside this module. In addition to its wide speed range, this intelligent motion controller also has a variety of motion control functions built in, such as 2/3-axis linear interpolation, 2-axis circular interpolation, T/S-curve acceleration/deceleration, numerous synchronous actions, automatic homing, and others.

A major advantage is that the majority of the I-8094A motion control functions are performed by the high-performance motion ASIC with little load on the processor. While driving the motors, the motion status, and the status of the other I/O channels on the PAC modules, can still be monitored. As the CPU loading requirements of the I-8094A is minimal, one or more motion modules may be used with a single PAC controller. ICP DAS also provides a variety of functions, and examples that can be used to reduce the need for additional programming by users, making it a highly cost-effective solution for motion control application developers.

Application

Specifications

Software
Development User-defined Macro Functions
SDK DOS 6.2
Hardware
Connector 68-pin SCSI-II connector
General
No. of Axes 4
Operation Mode Semi-closed Loop
Synchronous Action 10 activation factors and 14 actions
Speed Profile T/S-curve
Position Control Mode Incremental mode and absolute mode
Command Type Pulse Command
Auto-Home Search Yes
Input Signal Filter 2 ~ 16 ms, 8 stages
Axis I/O
Servo Interface Output SVON
Manual Pulse Generator Yes
Mechanical Switch Input Home, LMT+/-,
NHOME, EMG
Position Compare Output 10 KHz (X and Y only)
Servo Interface Input INP, ALM
Encoder Input
Mode A/B Phase, Up/Down
Ring Counter Mode 32-bit
Counting Rate 4 MHz (Max.)
Counter Width 32-bit
Pulse Output
Mode CW/CCW, PULSE/DIR
Counter Width 32-bit
Rate 4 MHz (Max.)
Interpolation
Circular Any 2 axes
Continuous Yes
Linear Any 2 to 3 of 4 axes
Digital Input
Channels -
Isolation 2500 Vrms optical isolation
Digital Output
Channels -
Isolation 2500 Vrms optical isolation
Power
Consumption +5 V @ 500 mA
Environment
Operating Temperature -20 ~ +75°C
Storage Temperature -30 ~ +85°C
Humidity 10 ~ 90% RH, Non-condensing

Download

Datasheet

Documents

Ordering Information

I-8094A-G  CR  High-speed 4-axis Motion Control Module with Internal CPU

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: