I-8094H-G CR: Module điều khiển Motion 4 trục tốc độ cao

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

I-8094H-G High-speed 4-axis Motion Control Module with FRnet Master and Internal CPU

Gọi +84 904251826 để được trợ giúp

I-8094H-G CR: Module điều khiển Motion 4 trục tốc độ cao

Features

• Independent 4-axis motion control
• Support for hand wheel and jog functions
• 2/3-axis linear / 2-axis circular interpolation function
• Continuous interpolation function
• Programmable T/S-curve acceleration and deceleration
• A maximum pulse output rate of 4 Mpps for each axis
• Pulse Output Types: CW/CCW or PULSE/DIR
• 32-bit encoder counter for each axis
• Encoder Pulse Input Types: A/B Phase or Up/Down
• Programmable automatic homing for each axis
• Position comparison management and software limits
• A wide range of synchronous actions (event-triggered actions)
• Expandable Remote I/O: 128 DI and 128 DO via a two-wire FRnet interface

Introduction

The I-8094H is a 4-axis stepping/pulse-type servo motor control module that can be used on any of the ICP DAS PAC series controllers, and is suitable for general-purpose motion applications. The I-8094H has the full functions of the I-8094A with the addition of an FRnet port, which allows the fast remote I/O of the module to be expanded easily. This two-wired FRnet can automatically scan its 128 DI and 128 DO channels within a period of 2.88 ms. The internal CPU allows the module to be used to perform motion operations without requiring a PAC. When working with a PAC, it also allows users to perform additional functions by integrating user-defi ned subroutines (Macro functions) from an external source, meaning that customized proprietary processes (know-how) can be embedded in the module. The I-8094H module also contains a high-performance motion ASIC. In addition to its wide speed range, this intelligent motion controller also has a variety of motion control functions built in, such as 2/3-axis linear interpolation, 2-axis circular interpolation, T/S-curve acceleration/deceleration, numerous synchronous actions, automatic homing, and others. A major advantage is that the majority of the I-8094H motion control functions are performed by the high-performance motion ASIC with little load on the processor. While driving the motors, the motion status, and the status of the other I/O channels on the PAC modules, can still be monitored. As the CPU loading requirements of the I-8094H is minimal, one or more motion modules may be used with a single PAC controller. ICP DAS also provides a variety of functions and examples that can be used to reduce the need for additional programming by users, making it a highly cost-eff ective solution for motion control application developers.

Specification

Software
Development User-defined Macro Functions
Library DOS 6.2

 

Hardware
Connector 68-pin SCSI-II connector

 

General
Synchronous Action 10 activation factors and 14 actions
Speed Profile T/S-curve
Position Control Mode Incremental mode and absolute mode
Operation Mode Semi-closed Loop
No. of Axes 4
Input Signal Filter 2 ~ 16 ms, 8 stages
Command Type Pulse Command
Auto-Home Search Yes

 

Axis I/O
Servo Interface Output SVON
Manual Pulse Generator Yes
Mechanical Switch Input Home, LMT+/-,
NHOME, EMG
Position Compare Output 10 KHz (X and Y only)
Servo Interface Input INP, ALM

 

Encoder Input
Ring Counter Mode 32-bit
Mode A/B pulse, Up/Down
Counting Rate 4 MHz (Max.)
Counter Width 32-bit

 

Pulse Output
Counter Width 32-bit
Mode CW/CCW, PULSE/DIR
Rate 4 MHz (Max.)

 

Interpolation
Cicular Any 2 axes
Continuous Yes
Linear Any 2 to 3 of 4 axes

 

Digital Input
Channels Expandable : 128 DI
Isolation 2500 Vrms optical isolation

 

Digital Output
Channels Expandable : 128 DO
Isolation 2500 Vrms optical isolation

 

Power
Consumption +5 V @ 500 mA

 

Environmental
Operating Temperature -20 ~ +75°C
Storage Temperature -30 ~ +85°C
Humidity 5 ~ 90% RH, non-condensing

Download

Data sheet

Documents

Ordering information

I-8094H-G  High-speed 4-axis Motion Control Module with FRnet Master and Internal CPU

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: